DIN EN 1428-2012 沥青和沥青粘合剂.沥青乳剂中水含量的测定.共沸蒸馏法.德文版本EN14280-2012

作者:标准资料网时间:2024-05-11 16:22:01 浏览:9374 来源:标准资料网

【英文标准名称】:Bitumenandbituminousbinders-Determinationofwatercontentinbituminousemulsions-Azeotropicdistillationmethod;GermanversionEN1428:2012
【原文标准名称】:沥青和沥青粘合剂.沥青乳剂中水含量的测定.共沸蒸馏法.德文版本EN14280-2012
【标准号】:DINEN1428-2012
【标准状态】:现行
【国别】:德国
【发布日期】:2012-03
【实施或试行日期】:
【发布单位】:德国标准化学会(DE-DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:Azeotropicdistillationmethods;Bindingagents;Bitumenemulsions;Bitumens;Bituminous;Construction;Definitions;Determinationofcontent;Distillation;Distillationmethodsofanalysis;Emulsions;Laboratorytesting;Materialstesting;Mathematicalcalculations;Petroleumproducts;Repeatability;Testing;Watercontent;Waterportion
【摘要】:
【中国标准分类号】:Q27
【国际标准分类号】:75_140;91_100_50
【页数】:12P;A4
【正文语种】:德语

下载地址: 点击此处下载

返回跳至顶部

上一篇: DIN 1045-3-2012 混凝土,加强和预应力混凝土结构.第3部分:结构的实施.DINEN13670标准的应用规则
下一篇: DIN EN 15882-1-2012 服务设备的耐火试验的结果的扩展应用.第1部分:导管.德文版本EN15882-1-2011

MIL-DTL-26518C, DETAIL SPECIFICATION: CONNECTORS, ELECTRICAL, MINIATURE, RACK AND PANEL, ENVIRONMENT RESISTANT, 200 DEGREES C AMBIENT TEMPERATURE, GENERAL SPECIFICATION FOR (19 JUL 2000) [SUPERSEDING MIL-C-26518B] [S/S BY MIL-DTL-83733]., This detail specification covers the general requirements for rectangular environment-resisting miniature rack andpanel type electrical connectors (plug and receptacle, intended for use in electronic and electrical equipment (see 6.1 for restrictionson intended use and application)).Product Code:SAE J1469
Title:Air Brake Actuator Test Procedure, Truck-Tractor, Bus, and Trailers
Issuing Committee:Truck And Bus Brake Actuator Committee
Scope:This SAE Recommended Practice provides procedures and methods for testing service, spring applied parking, and combination brake actuators with respect to durability, function, and environmental performance. A minimum of five test units designated A, B, C, D, and E are to be used to perform all tests per 1.1 and 1.2.Test ProceduresLeak rate-parking and service chambers (Section 4)Chamber volume-parking and service chambers (Section 5)Maximum release and hold-off pressure-parking chamber (Section 6)Force output and stroke-parking chamber (Section 7)Force output and stroke-service chamber (Section 8)Low temperature leakage-parking and service chambers (Section 9)Low temperature maximum release and hold-off pressure (Section 10)Low temperature force output-parking chamber (Section 11)Low temperature operational test-service chamber (Section 12)Corrosion resistance-parking and service chamber (Section 13)Mechanical back-off release mechanism (Section 14)Proof pressure test-parking and service chambers (Section 15)Cycle test-parking chamber (Section 16)Cycle test-service chamber (Section 17)Elevated temperature cycle test-parking and service chambers (Section 18)Vibration test (Section 19.1)Test Sequence ChartThe test sequence as charted in the 脪Test Sequence Chart脫 shall be mandatory (see Figure 1).PurposeThis document provides uniform procedures and methods for laboratory testing of brake actuators used in air brake systems.脩TEST SEQUENCE CHART